CCA-AppDS-Traffic Management Deploy and Manage Citrix ADC 14.x with Traffic Management Practice Questions
Prepare for CCA-AppDS-Traffic Management with more than an answer.
- Exam fee
- $200 USD
- Time limit
- 90 minutes
- Questions on the exam
- 55-60
- Passing score
- 61%
- Level
- Associate
- Valid for
- 3 years
Domains covered on the exam 12
- Getting Started with Citrix ADC7%
- Basic Networking7%
- High Availability10%
- Load Balancing14%
- SSL Offloading11%
- Securing System Traffic7%
- Monitoring and Troubleshooting9%
- Policies and Responder9%
- Rewrite and URL Transform7%
- Content Switching7%
- Optimization5%
- Global Server Load Balancing (GSLB)7%
- 1
An administrator is deploying a NetScaler HA pair across two different data centers connected by a Layer 3 link. The NSIP of Node A is 10.1.1.5/24 and the NSIP of Node B is 10.2.1.5/24. What specific HA configuration must be enabled for this pair to form successfully?
Show answer details
Correct answer: D
When NetScaler nodes in an HA pair reside on different subnets (Layer 3 HA), Independent Network Configuration (INC) mode must be enabled. This prevents the primary node from synchronizing its SNIPs, VIPs, and routing table to the secondary node, which would cause IP conflicts in the secondary site.
- 2
A NetScaler HA pair is experiencing unexpected failovers. Upon reviewing the logs, the administrator notices that the physical interfaces are up, but a critical backend subnet becomes unreachable from the primary node, triggering the failover. Which HA mechanism was configured to trigger this behavior?
Show answer details
Correct answer: A
A Route Monitor allows the NetScaler to monitor the reachability of a specific route. If the route becomes unreachable (even if the physical interface remains up), the Route Monitor triggers an HA failover to the secondary node, assuming the secondary node can still reach the network.
- 3
An administrator plans to upgrade a NetScaler HA pair using the In Service Software Upgrade (ISSU) feature to achieve zero downtime. Which TWO conditions are strictly required for ISSU to function correctly? (Select TWO)
Show answer details
Correct answer: A, B
For ISSU (In Service Software Upgrade) to work properly and migrate connections seamlessly during an HA failover, both nodes must be identical in terms of hardware/virtual resources and licensing. Additionally, ISSU is only supported between firmware versions that are explicitly listed as compatible for ISSU.
For ISSU (In Service Software Upgrade) to work properly and migrate connections seamlessly during an HA failover, both nodes must be identical in terms of hardware/virtual resources and licensing. Additionally, ISSU is only supported between firmware versions that are explicitly listed as compatible for ISSU.
- 4
A healthcare organization is looking to consolidate multiple independent hardware load balancers into a single physical appliance. They require hardware-level isolation for different tenants to maintain strict compliance and resource separation. Which NetScaler ADC form factor is specifically designed for this deployment scenario?
Show answer details
Correct answer: D
NetScaler SDX is a specialized hardware appliance that runs a hypervisor, allowing multiple independent NetScaler VPX instances to run on the same physical hardware with strict CPU, memory, and SSL resource isolation. MPX is a single-tenant hardware appliance, VPX is a virtual machine, and CPX is a containerized form factor.
- 5
During the initial setup of a NetScaler ADC 14.x appliance, an administrator must assign an IP address that will be used strictly for management access via SSH and the GUI. Which IP address type should be configured for this purpose?
Show answer details
Correct answer: B
The NetScaler IP (NSIP) is the management IP address of the appliance. It is used for accessing the management GUI, CLI (SSH), and for HA synchronization. SNIPs are used to communicate with backend servers, and VIPs are used to receive client traffic.
- 6
A financial enterprise is planning a new NetScaler ADC deployment. Their primary requirement is that the NetScaler must be logically placed outside the direct path between the clients and the backend servers to avoid altering the existing network topology. However, they still need the NetScaler to perform load balancing by having clients point to a Virtual IP (VIP). Which deployment mode describes this architecture?
flowchart TD Client --> Router Router --> Switch Switch --> NetScaler_VIP Switch --> Backend_Servers NetScaler_VIP -.-> SwitchShow answer details
Correct answer: E
In a One-Arm deployment, the NetScaler ADC is connected to the network using a single interface (or aggregated link) and sits parallel to the servers on the same VLAN/subnet. It does not act as a physical bridge or router between the client and server networks, meaning existing network topology requires minimal changes.
